Asus P4g8x Drivers For Mac
ASUS P4G8X Deluxe: BIOS and Overclocking The P4G8X utilizes Phoenix Technology's Award BIOS, which seems to be the most popular BIOS for power users these days. BIOS hardware monitoring is powered by ASUS's ASB100-A Bach chip. The Hardware Monitor section includes some fairly normal readings and information in general. Here you'll find readings on motherboard temperature, CPU temperature, power temperature, fan speeds (CPU, power, and chassis), Vcore, PSU readings (all rails), and an option for enabling ASUS's Q-fan technology.
Q-fan is a nice little BIOS option to have, as it regulates your CPU's fan speed based on how taxed your system is at any given moment. CPU temp readings were right where we expected them to be, between 39C and 41C. Normally called the Advanced Chipset Features section, the Chip Configuration section included some fairly nice DRAM tweaking as well as other such options. In Chip Configuration, it's possible to adjust DRAM timing mode, CAS Latency, Precharge to Active, Active to Precharge, Active to CMD, and Idle Timer (which doesn't really boost performance at all) among other minor options. There are no Bank Interleave or Command Rate adjustments available, but that's normal for Intel-chipset based motherboards these days. All in all, the Chip Configuration section lives up to the tweaker's needs for the most part.
With Intel's E7205 chipset, the highest memory speed possible is 266MHz (dual channel operated) if your FSB is operating at stock speed (133MHz). Since there are no other divider options available in the BIOS or via onboard jumpers or switches, the only way you can increase your memory speed is by increasing your FSB. If you raise the FSB of your processor to 166MHz (666MHz effective FSB), assuming you have a good enough processor, you can run your memory at DDR333 (dual channel). However, since dual DDR266 already maxes out the bandwidth that 533MHz FSB Pentium 4 processors can handle, there's no need to overclock unless, of course, you're an overclocker.
The P4G8X BIOS does include some fairly good voltage tweaking options. In 0.1V increments, you can adjust VDIMM up to 2.7V, which is adequate for most users, considering that overvolting memory doesn't usually yield a significantly better overclock. VAGP is also adjustable in 0.1V increments; as high as 1.7V. ASUS goes all out with the Vcore options, allowing as high as 1.975V in 0.025V increments. 1.975V should be plenty for most people, as running any modern day Pentium 4 CPU at 1.975V will significantly reduce the lifespan of the CPU. For once, ASUS produces a board that doesn't overvolt, since Vcore (as read through the Hardware Monitor) consistently reads a dead-on 1.5V.
Like every other 845-based motherboard we've tested in the past, the ASUS P4G8X comes with an independent AGP/PCI lock running at 66.67MHz/33.33MHz, and adjustable all the way up to 104.46MHz/52.63MHz. This is a vital feature to have for overclockers, as running your AGP or PCI cards too far out of spec can damage those parts. For non-overclockers, it's still a nice BIOS option to have. Overclocking the ASUS P4G8X Deluxe was a cinch.
The following table lists the components we used for overclocking the FSB: Front Side Bus Overclocking Testbed. Enermax 300W This is quite a conservative and cheap overclocking setup, but every since its inception P4 Northwood processors have continually been able to outperform AMD's Thoroughbred processors overclocking-wise, making us more impressed by the day with Intel's 0.13-micron process.
That said, we were easily able to hit 160MHz FSB, or just over 2.70GHz core clock. This is certainly not out of the ordinary for an Intel chipset based motherboard. We weren't able to conduct any memory overclocking tests due to the fact that this motherboard only contains a 1:1 divider.
However, have no fear, ASUS is coming out with a motherboard based on SiS' 655 chipset, which supports dual channel DDR333. It'll be interesting to see how much performance gain there is with dual channel memory running at 400MHz and beyond on SiS 655 motherboards.
2 Comments. Friday, January 07, 2005 - Regarding previous comment: And I told this thing to show e-mail address. If anyone has questions. It also removed paragraph indents that would make the above post a bit more readable- apologies. And a clarification: The ZCR card could be seen to be flashed only because a jumper change is needed to put them in flash mode. In normal mode, the Thunder K8S Pro S2882 BIOS was squashing the Adaptec 2010S / 2015S BIOS. Damn, I hope Google indexes that comment well.
Speaking of which, for you-know-who: Tyan Thunder K8S Pro Adaptec 2010S 2015S ZCR RAID BIOS problem incompatibility bug hang failure download flash PCI-X Tyan 2882 K8S Pro Thunder ZCR Adaptec 2015S 2010S RAID bug hang failure problem incompatibility PCI-X flash BIOS download Thunder Tyan 2882 K8S Pro ZCR Adaptec RAID 2010S 2015S BIOS incompatibility problem failure hang PCI-X BIOS bug flash download wildly incompetent screen-reading technical support monkeys beta-testing on customers See previous comment. Friday, January 07, 2005 - Anandtech's evaluation covers how good Tyan's tech support is in the absence of any real problem for them to deal with.
I would suggest that this is not an adequate criterion. Our experiences were different. The issue of product quality is relevant here, since it makes the quality of technical support more important if the product is poor. My company tried Tyan boards several years ago, and gave up when along with 4 DOAs, 3 quick in-service failures gave a defective rate of almost 50%. I mistakenly thought almost 10 years would be enough for the company to straighten out. We ordered 3 Thunder Pro S2882s for a client taking a website inhouse who wanted a 64-bit option- this was before Intel's 64-bit Xeons showed up. All of the following happened under time pressure, which isn't unusual, and why better support than Tyan's is necessary: One of the three boards was DOA; wouldn't flash any of three Adaptec 2010S ZCR cards; the other two would.
Tyan's tech support essentially kept assuming we were doing something wrong and, and at one point asked if we had the current BIOS on the ZCR cards. They must not have any sort of decent database, since the problem had to be explained anew every call. After they admitted the board was bad, they failed to warn us of their shipping deadline for replacing the board (which they will do, and with an E. Coast vendor and them in CA was necessary). All the boards failed to see the ZCR cards. First tech said that couldn't be happening, second knew about the problem and said the 'E' BIOS fixed it. Update r on mac. We delivered servers with drives unmirrored.
Site setup was busy for a while. When I finally had a chance to work on ZCR problem, Tyan could find no record of the problem (none of the emails we exchanged except ones I sent had case #s in the header). I explained everything again, and once again had to assure them again that we'd gotten the obvious stuff right. First tech said he didn't know how it could be happening, and thought I was missing something. Got email next day from supervisor acknowledging there was a problem and saying (again) they had a new BIOS out that would fix the problem. Downloaded, sent tech onsite to install.
Didn't work, same result- ZCR card option grayed out in BIOS, system hangs. When I had a chance to go down and work on it personally, once again, no record of case.
Asus P4g8x Drivers For Mac
I went through everything from scratch once more, assuring them that yes, we'd read the FAQs and yes, the system was plugged in, and yes, we had tried every possible combination of their two blasted relevant jumpers, and that in fact there were about eight other germane parameters we had tried which none of them had thought of- and all of this while wasting valuable onsite time. When I finally convinced them that 1) we were competent and 2) it wasn't working, I was told I'd get a call back 'shortly' from the responsible engineer.
Three hours later, in a darkened factory, at 5:14:55 just as I was leaving, I got a call back from the engineer who actually knew what was going on. He finally admitted we had everything right. He had no solution, but agreed with my suggestion for testing and said he'd check- he lacked authority(!)- to see if management would authorize the replacement board I'd been asking for. And they did, but there shouldn't have been any question. Next trip down I replaced the board in one server, picking the server in whichhe Gigabit Ethernet ports had failed- and it still didn't #$%^& work. Tyan said it had been working the day before for them with a 2010S ZCR card, and until today, I didn't know whether they were lying or not. I cussed some and ordered $1200 worth of controllers to replace what Tyan couldn't get right 5 months after the product's release.
Today I checked and saw that they have a new BIOS for the board available that 'Fixes PCI ZCR card hangs system during POST'. It's the third BIOS for which they've made that claim, and you know, it really doesn't matter whether they're right this time or not. And if they're not, it doesn't matter whether they're just mistaken or actually lying- theend result is the same. We saw five of their high-end server boards. One DOA, one in-service failure, all five with a major design flaw.
Eight years is enough time to take care of company-wide failures. Any company that will release a $500 server board with a 40% failure rate, and without first ensuring that everything on it actually works, and who then can't tell for five months whether or not they've fixed the resulting problems, and whose tech support is staffed with folks who can't deal those problems- well, that's a company whose products you want to steer very clear of.
Update the ASUS P4G8X Motherboard Drivers For Windows XP with ease Easy Driver Pro makes getting the Official ASUS P4G8X Motherboard Drivers For Windows XP a snap. Easy Driver Pro will scan your computer for missing, corrupt, and outdated Drivers.
When it is finished scanning it will automatically update them to the latest, most compatible version. Easy Driver Pro makes keeping your ASUS P4G8X Motherboard Drivers For Windows XP update to date so easy even a child can use it. Installation Instructions. to begin the Easy Driver Pro download.
Click “Run”. (Click ”Save As” if using Firefox).
Asus P4g8x Drivers For Macbook Pro
Click “Run” Again. Follow on-screen directions for installation.Note: If you want to install the drivers manually for free you can visit the device manufacturer's website to download the latest versions. How Easy Driver Pro Updates ASUS P4G8X Motherboard Drivers For Windows XP? Easy Driver Pro performs a complete scan of your all of the devices in or attached to your computer. It checks everything such as sound card, graphic card, monitor, mouse, printer, etc.
To see if you have the latest, most compatible device drivers installed. It can determine which ASUS P4G8X Motherboard Drivers For Windows XP are either missing, corrupt, or have become obsolete. Next, Easy Driver Pro searches a database of over 11 million drivers and matches missing, corrupt, or obsolete Drivers to the latest, most compatible drivers for your operating system. Before install the new drivers, Easy Driver Pro backs up your existing Drivers and settings to create a restore point just in case one of the ASUS P4G8X Motherboard Drivers For Windows XP turns out to still be incompatible. Easy Driver Pro updates your Drivers, based on the scan, and matches to the latest most compatible versions. Note: Easy Driver Pro does not sell or charge for drivers. You can install the drivers manually for FREE.
Easy Driver Pro free scan will find all the outdated drivers on your PC. Visit the device manufacturer's website to download the latest versions. Or Easy Driver Pro registered version (49.95$) can do it for you if you choose this option. Also, we might offer Easy Speed Check test app, Easy Speed PC and PC backup offers. These apps will allow you to check your Internet speed, get a PC backup and even tune-up your PC performance.
'Expert Recommended.'